Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Dear support team,
Currently, I create a custom board using nRF52833-CJAA SoC, but I not found nRF52833-CJAA package in nRF Connect SDK v2.7.0.
Could you please help me...
I'd like to make my product appear as a USB drive when plugged into a computer. I want to save sensor readings to CSV file, and allow users to read/copy them.
I found the...
I am currently working on encrypting "Provisioning public key PDU" with a public key of end node that was received out of band the by provisioner before transmitting it to...
Hi, all:
I use 9160DK to test GPS standalone mode as follow steps with AT command example：
Approach 1:
1、set ”AT+CFUN=0“ to power off mode;
2、set " AT%XSYSTEMMODE...
Hello,
I am using three nrf52840 DKs to test sending gatt notify data. They are one peripheral and two central.
When they each have only one Gatt Customer Service, peripheral...
Hello,
I'm facing a problem in pc-ble-driver-py. I adjusted the uuid_count, but the code still fails at the service discovery line:
ble_adapter.service_discovery(new_conn...
I try to use st25r3911 and try to achieve low power consumption.
The code configures interrupts: gpio_pin_interrupt_configure_dt ( & irq_gpio , GPIO_INT_EDGE_TO_ACTIVE ...
Hello,
I work with the Zigbee Light Switch exemple from SDK 2.7.0
After association, the device never use the Poll data as for end_device role. But, it sends continuously...
We have created Thread Network include Leader, router and end devicewitch nRF SDK v2.5.0 on nRF 52840
We found the Thread connect will offline after 15 minute and not reconnect...
This is a higher-level question because I'm having difficulty finding concise and clear practices for this sort of thing. I don't want to go implementing something subpar...
Hi folks,
I'm making an application which needs to transmit a few kB of config data (for a configuration utility), and I was hoping to do it via UART.
To that end, I loaded...
I am working on specialized PCB's for my job, and we are trying to capture modem traces for our devices. Via JTag, I have serial access to pins P0.05 (TX) and P0.06 (RX) of...
Hi All
I m developing a project in nref9160, in GNSS part, I need to use PGPS, but can I control the checking in nrfCloud? sometimes it go to download PGPS and make GPS...
Dear Nordic Developer Zone,
I am working on MAX30003 ECG ( https://datasheets.maximintegrated.com/en/ds/MAX30003.pdf ) with Nrf52840-DK. My sensor is work on the 32.768kHz...
Hi,
I have been having quite a lot of issues around connectivity and my device, all of which at this point has stemmed from MNO blocking activity from MVNO's ( here and...
