Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
I still have problems understanding the port and pin assignment for peripherals on the nrf54L15.
I need up to three SPIM, one UART and one TWI. That should work, right...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hello,
I recently bought a Thingy91x; before that, I was using a Thingy91. I activated it and successfully programmed the Hello nRF Cloud firmware via the Quick Start in...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hi,
I'm working on an nRF5340 + nRF7002 project using Zephyr RTOS , where the device enters low-power sleep and wakes up on a hardware counter alarm ( counter_set_channel_alarm...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
Our design has an nRF5340 with RV3028C7 to provide the 32 kHz clock via P0.00.
If I configure P0.00 as a digital input, I can see the pin toggling.
However, if I use the...
Hi
board: nrf52832 DK
sdk: nrf connect sdk v2.6.1
I have successfully integrated the provisioner and light switch client together. Now I can control the light switch...
Hi, With this setup in , I successfully built a CIS mode using my nRF5340 DKs , enabling stereo sound while the microphone is active .
However, I am currently experiencing...
So as the title... the Creating a custom driver using the sensor API exercise for the current SDK versions is missing from the nRF Connect SDK Intermediate course. Are there...
Hi,
Is there is an option to disable NRF Cloud message storage when we are using a message bridge or message routing to retrieve our data from NRF Cloud? This is to reduce...
Hi,
I was working on Channel Sounding for my NRF54L15 boards and suddenly the boards in "connected devices" were no longer visible. I don't know how it happened and what...
Good morning,
I would like to know if it is a good idea to store serial number on UICR register when using nRF9160 at production stage.
If using UICR, which register should...
