after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I have added " config HW_STACK_PROTECTION" in KConfig file of the board.
Is there a way I can check during runtime if the Stack Protection is enabled? Is there any...
Hello
I am building a hardware that requires to use the nRF9160 together with the nRF52840, in order to add the 2.4GHz radio support to the system and also to be able to...
Hi,
Is it possible to run nRF5 SDK for Mesh examples on nRF Connect SDK for Bluetooth Mesh using nRF52840 Dev Board?
Examples are available on this github page.
https...
Hello,
I am trying to make GPIO P0.07 to high, in my nrf5340 Audio DK. Externally I am connecting an LED between P0.07 and GND. But it not showing any voltage between them...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi,
I want to know how to find the pack of nRF5 SDK.
Because the previous URL has expired. (http://developer.nordicsemi.com/nRF51_SDK/pieces/nRF_DeviceFamilyPack/ )
Hi Nordic
In the documentation of Zigbee sample of nrf Connect SDK, it said:
>>
Support for Zigbee R22 has been deprecated in nRF Connect SDK v2.8.0 and it will be...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Greetings,
We have a PCB with nrf52 and nrf91 on it.
We have nrf9160 firmware with MCUBoot. The chip boots into mcuboot dfu mode when a certain pin is set to high during...
Hi all,
We are running v2.4.0 SLM in nRF-9160 as pure modem, communicating with our external MCU. And we need to send a MODBUS-TCP write request command about each 10 seconds...
Hello.
Thank you very much for releasing nRF Connect SDK v3.0.0-preview1.
I quickly tried the sample program, and while the build was successful, I encountered an issue...
Hi everybody
I'm trying to modify the Zephyr serial LTE modem example so that CMUX can be controlled using another communication interface, specifically I'm imagining...
Our application is designed to remain connected to the network - sending data every 10 minutes or so. We've customised the asset tracker v2 application, as this provides the...
NCS v2.6.0, devices based on nRF52840 (Fanstel BT840)
The project is a star network in which the Central is housed in a steel enclosure with a patch antenna perhaps 1cm...
I've been working on a peripheral wich accepts Just Works pairing requests and I'm completed at all points but the pairing itself. The device advertisises and connects successfully...
