Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
DK: v0.9.0 nrf: v1.2.0 supl fw: v0.5.2 modem fw: v1.2.0 OS: Windows10
I'm trying to use assited GPS in "gps" sample program, but it doesn't work. This is log. There is no...
Dear Nordic,
We are developing the Cat M1 module base on the nRF9160 V1.2.0.
When we try to evaluate the current consumption in eDRX mode, we found our module even unable...
Hi,
We made a custom board with nRF52 and it's BLE radio doesn't advertising, not visible on nRF connect APP. I tested a lot of example, like uart_peripherial,heart rate...
Is it possible for the Android-nRF-Mesh-Library to be used to serve models and also proxy/relay other on-Android nodes?
I’ve developed an Android 8 app for a tablet and...
Hi Nordic Tech Support,
Our company is going to use Nordic nRF52832 on our next generation wireless product. I am the software engineer and doing the evaluation these days...
I am using Thread/ZigBee SDK v4.0.0 as a coordinator. I have no zigbee routers in the network so all of the end devices in the network join the coordinator. When I issue a...
My current project has DFU enabled through the secure BLE bootloader and it works well. I would like to include the additional option of performing DFU over USB. Is it possible...
Hi, I'm testing the MQTT implementation integrated in the NRF5 SDK.
This is my test environment: - A nRF52840 board with the MQTT publisher example from the SDK. - A Raspberry...
Hi,
We want to be able to upload a new firmware in my nrf52832 without serial connection.
I am trying to set up DFU over BLE and I stumbled upon few problems along the...
I'm porting an application from nRF52832, SDK 14.2.0, SD 5.0 to nRF52833.
I want to do this in two stages:
As quickly as possible validate our first prototype board...
Hi,
Using the RTC example in the 'nRF5 SDK 16 / examples / peripheral' as a starting point, we've programmed the rtc_handler to execute at regular intervals approx. every...
We are using libnrf_cc310_0.9.12.a. This doesn't work with position independent code check box in IAR (see Project Options->C/C++ Compiler->Code->Code and Read Only Data ...
Hi,
I'm trying to enable a HW timer (TIMER1) in my BLE application. I'm using SDK 16, and following the pattern shown in examples/peripherals/timer. However, when I get...
Hello
We have a project in which we need to be broadcasting data (around 30 bytes of message) to 150 unit via BLE.
we are thinking of using the nrf52832, which we...
Is it possible to read the value of APPROTECTSTATUS via the firmware? It seems like the AP register in not memory mapped, so maybe not. But maybe there is some kind of work...
