Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi, i have written code in android, where i am using threads to connect to 832 ble over insecure RFComm socket..
Am not pairing with 832 in my app and am directly trying...
Hi I am implementing a buttonless_DFU function right now. I decided to do Buttonless on my project's PCB Board because it is no longer an environment where I can add switches...
My setup is as follows:
nRF5 SDK 13.1 with s132 5.1.0
nRF52832_AA
Keil 5.25pre
I use RTC1 counter for timestamping along with app_timer timers. My get_timestamp() function...
I am trying to send lots of data through radio (basing on old micro esb project from github, but heavily modified).
I need to keep radio IDLE (not DISABLED) when not transmitting...
Hi,
I am developing smartphone controlled BLE door lock based on nRF52840.
The door lock is a peripheral (also GATT server) and the smartphone is central (GATT client...
Using the nRF52840 with SDK15.3.0 and S140, I am seeing strange interactions between PWM and BLE.
The PWM is configured to create a continuous 175kHz output just under...
I am currently developing with nrf52832 sdk14.2. When nrf52832 is bound to a different iphone connection, if the stored binding record of nrf52832 is already full, will the...
Hello,
We require a bluetooth low energy IC with MCU. Right now we are testing with nrf51422 development board. Could you please suggest any updated ICs with (BLE+MCU) ...
Hi
Below picture and attached file is my 52810 hardware.
All the component are accord with the 52810 data sheet.
But, when I download the BLE blinky project from the...
Hi I am currently testing Buttonless DFU using SDK 12.3, nRF52832 DK. Example test was conducted first using the DK board, but as you can see in the picture, it will fail...
Hi,
I have a MQTT-sample based application running and everything works fine. If I supply the DK through a USB cable connected with my computer, LED 5 blinks high frequently...
Hi,
I am using nRF5 SDK 15.2 and the twi_sensor example to read over I2C a slave device 'WhoAmI' memory location. I first tx the slave address (0x68) and then attempt to...
Hi,
I am using nRF52832 mcu, trying to run the flash data storage example but is having some trouble.
I followed the instructions to set up the terminal setting for UART...
Hello
Hello Using nRF5_SDK_12.3.0 examplesble_centralble_app_multilink_central as a host to send data to slaves and receive data from slaves is no problem. The problem is...
