Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I have two nrf51822AC mcu chips that are integrated on custom boards, and I need to communicate between those two chips (one set as a transmitter and the other as the receiver...
Hi,
I own company that builds a PIC 8-bit devices, and can code at a low bit level in the PIC environment.
I picked up the NRF52 Dev board, and am trying to learn the...
My peripheral device connects with central one very rarely. I decided that I don't want peripheral to negotiate connection parameters with central, just use settings imposed...
I'm developing custom board of nrF51822 CEAA (256k, 16k)
I set my bootloader ROM, RAM just like below
as I understand,
Firmware size should not larger than...
hi,
i just ask about nrf52832.
im using it with keil compiler and trying to divide the memory section (it that will be update and not)
but i have hard time to do with keil...
I'd like to log some debug stuff to a mobile app over BLE, when in a connection, using the NRF_LOG library and the Nordic UART service. I have this working just fine without...
I'm trying to write to specific address on flash memory (data region) for debug purpose using
nrfjprog.exe --memwr 0x3B820 --val 0xAA000000 --verify
but when I read...
So I'm still trying to get my way around the DFU service implementation, and I'm currently having trouble with the first step, which is to enable the control point notification...
Hi.
This is a bit of a combo question:
I recently got the nRF52 10040 and I'm trying out the included examples on uVision5.
I only managed some examples to...
I am working on BLE Applications, I have tested with different devices like Nexus, Moto, Samsung, LG(ble V 4.0). I am getting the GATT Error 133 in Samsung Devices alone(Samsung...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hello Nordic,
My goal is to control a small device with NRF51422 without any other additional controller. So I’ve developed my own PCB and I’ve used the example ble_app_uart_s130_pca10028...
Hi,
I have an nRF52 chip that has likely exceeded the flash endurance limit.
I am observing that after an ERASEALL, not all bits are erased, but after retrying ERASEALL...
