Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello All,
I have been trying to get the Xiao BLE Sense with the nrf52840 chip in conjunction with the expansion board to access the SD card using the FatFS example from...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
Hello,
OS: Ubuntu 22.04
SDK version: NCS 2.6.1
Modem firmware version: nrf91x1_v2.0.1
We are evaluating NRF9151 in a new design. We have some prototypes built...
For a project we need to evaluate DECT NR+. We have used the `hello_dect` example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/dect/dect_phy/hello_dect...
Hello, I'm developing an app that will allow a programmer to flash application firmware and modem firmware. I am able to flash application firmware via JLink Commander. The...
Hi, I had a project which was configured with upto 5 simultaneous connections. Recently moved from NCS 2.4.1 to 2.6.1 and now the advertising stops after one connection. I...
Hi,
I want to DFU the nRF52 from nRF91 over UART. And I find this sample: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/lwm2m_client/fota_external_mcu...
We are working with Zephyr to program the development kit for now and later the real board,
We need access to both UART0 and UART1 but we can't seem to get UART1 to work...
Attempts to build the Matter light bulb same fail for me under these conditions:
A new nRF Connect SDK install on Ubuntu
Toolchain v2.7.0
SDK v2.6.1
VS Code...
Hi,
For Production I need to program by SWD 10 nRF52832 devices simultaneously. The production tools will be prepared for separately connecting 10 SWD interfaces to 10 different...
Hi.
I am experimenting with an internal temperature sensor (TEMP) on an nRF52810 microcontroller and have some questions:
1. How to select a crystal oscillator as a source...
We are developing nRF52840 battery powered device, NCS 2.5.2.
Wanted to use shell for external commands for system testing (currents must be low when the debugger is not...
