Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
1.
2.
Hello. It is under development as nrf7002.
I'd like to ask you about the quasi-board configuration I saw in the sample example.
The target board in...
When I build the system using system default, use save minimum configuration，The chip-related configuration is also saved to my application configuration prj.conf, which it...
Hello everyone,
I am currently using Nordic NRF5340-DK board for development and I have run the zephyr UART driver sample that works an echo bot. This sample works fine...
Hi,
I'm trying to retrieve the MCUBoot version inside my application (from the VERSION file).
In the Zephyr documentation ( docs.zephyrproject.org/.../index.html) , I...
nRF 52832 DK advertizes successfully .
But the name of the DK is not listed in nrf connect for mobile app. Peripheral_UART is the sample code that I have compiled.
Hi All.
Trying to complete Lesson 6 Exercise 2 from the course nRF Connect SDK Fundamentals made by the DevAcadeny, I connected the Thingy53 to my computer through USB-C...
Hello,
I am currently on a project where we have 4 BLE peripheral devices equipped with NRF52840 connecting to one BLE Central, which is an app on iOS or Android. From time...
Hello,
I am seeking guidance on the following issue:
Development Environment
IDE: Visual Studio Code
Toolchain Manager: v1.3.0
SDK: ncs v2.6.0
OS: Windows 11...
Hi,
We're planning to integrate ble_app_uart and ble_app_uart_c into our project. Before integration, we tested the ble_app_uart example code on one development board. After...
Hello,
I am using two nrf52840 DKs to test ble transmission and i2s output. The nRF Connect SDK I use is v2.6.0.
Both of them are ble connected. One sends data to the...
Hi all,
I'm trying to get a UART connection running at 460800 bps, and it fails about 1-5% of the time, meaning that I receive less bytes than I expect. This happens a lot...
Hi,
I want to debug [i.e. attach to and single step] mcuboot [running as second stage bootloader] using Ozone and JLink.
I can connect to the board via the debugger...
I added my own overlay to the website routine "ncs-fund\v2.8.x-v2.7.0\l5\l5_e1_sol". The contents are as follows
/////////////////////////////////////////////////...
1.After I burn AP CODE, executing "nrfjprog -f nrf53 --program factory_data.hex –sectorerase" instruction will cause the following error. This issue wasn't happened in prior...
