I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I'm able to select the nRF21540_nRF52840DK board for my project and I'm wondering how command the nRF21540 using the I/O pins and the SPI port. Do you have any examples...
I have to make a connection from a central_uart to 4 periperal_uart every 60ms Sending 30 byte .
I Have to make a polling of all the peripheral every 60ms.
I know that...
Device: nRF52811
Board: custom (EYSNSNZWW module is used)
SDK: 16.0.0
SoftDevice: S112(v7.0.1)
Sample Project: ble_app_uart
Hello,
Is it possible to read BD...
I have a custom board based on nRF52840 with some custom peripherals : LEDs, buzzer, buttons, etc
To get my app working I copied the nrf52840dk_nrf52840 board from the 1...
Hi,
I started using the Nrf5340-DK with the openthread cli sample. It works fine, and now I'd like to move the main UART to pins P0.24 and P0.26.
To do so, I created...
Hello, I've been trying to migrate my code which uses NRFX SPI functions to NCS 2.0
The code compiles just fine on NCS 1.9, but after migrating to NCS 2.0 I noticed that...
I have just been hired to this company and they have assigned me to repair some of their defective modules. The modules are BL651 with what I believe to be nrf52810 processor...
Hi,
is there a driver available for the VM3011 microphone that comes with the Thingy:53?
The chip has some power-saving and wakeup features that are configured using I2C...
Hi,
We are having some issues communicating with a Winbond W25Q64 flash memory. Using the standard SPI Zephyr drivers an attempt to get the Manufacturer ID returns 0xDC...
Hey!
I am working on a zigbee asset tracking system for my thesis. Got myself 3 nrf5340 boards and a sniffer.
Unfortunately i can't manage to get started with zigbee...
Hi everyone!
I have recently been trying to flash the 'blinky' zephyr sample to the nRF5340 Application Core on the R4D4 Control Board. I am yet to have any success, by...
Hi there
I'm using Asset tracker v2 as a base for my application with AWS, however I wanted the FOTA to download to external flash, as the Asset tracker application is large...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 with MCUBoot and want to upload firmware updates for the application core using mcumgr.
I use the hello_world sample in...
We are migrating from Modem firmware version 1.2.x to 1.3.x. Since it is now possible to enable LTE and NBIOT both using the following XSYSTEMMODE configuraton:
How does...
I'm trying to develop a Bluetooth mesh network with low power consumption.
Is the performance the same when comparing firmware using the nRF5 SDK for Mesh and firmware using...
