I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I am working with an nRF5340 DUT and I would like to perform a throughput test . I have my own BLE peripheral/central application (developed separately) and I want...
I’m working on a custom board based on the nRF54L15. I’m using MCUboot Serial Recovery over UART and I’m seeing a repeatable issue I can’t reconcile with the docs.
SDK/Tools...
Hi, I'm working with multiple versions of the nRF Connect SDK (v2.8.0, v3.0.0, v3.1.0) using the official VS Code integration on Windows and could verify this also on Ubuntu...
Hi, I am trying to run the Wi-Fi STA sample on nRF7002DK .
With nRF Connect SDK v2.9.2 , the STA sample connects successfully to my Wi-Fi AP (router).
With NCS...
I am using vscode on linux, I started by programming the blinky sample onto the devkit, without issue. I then moved on to the gnss sample in a separate project, this worked...
When we run test case SED&MED 3.5 , the following inconclusive result happens:
COM78 command: ot test tmforiginfilter disable COM78 FUNC __executeCommand failed: Error 35...
Hello everyone,
I need to save a core dump on my NRF54L15 internal flash in order to debug an issue. I've been following the "Debugging and Troubleshooting section" of the...
Hi everyone,
I am facing an issue when modifying the peripheral_nfc_pairing example.
Due to hardware limitations, my device cannot integrate an NFC antenna. Instead, I...
Hello. We are evaluating the nRF9151 SiP as a potential solution due to its low power consumption and compact form factor . However, our team has limited experience with firmware...
Hi,
I'm considering the implementation options for nRF91 GPS front end. Having a shared antenna for LTE and GPS would be tempting, but I'm concerned about the filtering...
Hello,
I am trying to get some basic examples working with my new NRF9151DK and running into quite a few issues. Note that this is using a onomondo sim card that came with...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
