I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I'm having trouble connecting the Thingy:91 to LTE network.
I'm using the thingy91_fw_2021-06-28_7a076c22 example.
I flashed correctly the thingy91_asset_tracker_v2_nbiot_2021...
Dear Nordic team,
We are deveopping BLE & ANT enabled display. Because it is a mass production product we need to do an automation for asigning devices destinguesed ID....
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
Hello,
Out application is using the time slot api to generate ~29ms (35Hz) burst of pulses.
Occasionally, the interval between two adjacent pulses extends to ~35ms ...
Dear Nordic support,
I need to clarify a few points using SAADC for battery measurement - running the ble_app_proximity application without modification. I measured the...
hello, i hanve a problem when i use usb transfer data to pc with ep1, sdk 17.0,nrf52840dongle
I have many data(more than 100KB) transfer to pc,when I send the data for once...
Hello,
I am using the nrf52840 for the application, basically i want to use the timer driver in my code.
so basically if i have 5 timers of nrf52840 and i am using one...
I am using a nRF52840 Development Kit to flash a custom board with a nRF52840. When I use the nrfjprog -p (or --pinreset) option to reset the CPU, it will consume over 1mA...
I am using nRF52833 on ncs to turn on the extended broadcast. After referring to the corresponding settings, I found that the transmit power setting does not take effect....
In standard sdk 17.0.2 is it possible to know which devices did i accidently disconnect?(Interactive command s140)
for example
my central is the interactive command...
Hi, I used NRF52 DK and NRF Connect SDK 1.6. I used the st_ble_sensor sample with no changes. When I press Button 1, I expect to get a notification on the central device....
Is there a straight forward guide that demonstrates how to changes the Asset Tracker V2 application from "Active Mode" to "Passive Mode"?
Referencing the notes on the application...
Hello,
I have been working with nRF52832 microcontroller on a custom PCB. Currently, we are implementing OTA updates through BLE, and developing using the nRF toolbox app...
