Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
i'm trying to compile the asset tracker v2 for the nRF9160-DK but i get the following error:
"opening dependency file modules\mcuboot\boot\bootutil\zephyr\CMakeFiles...
Hi all
I have Openthread setup
BorderRouter [ with Raspberry pi and nordic in NCP design].
EFR32 radio board that has been flashed with ot-cli-ftd and made as Leader...
Kindly confirm modem details, BIP ,Refresh command support etc. as mentioned in sheet. -- Kindly let me know whether the question from the operator is clear
Chip nrF52810
SDK - 17.0.2
SD- S112
Mine is a system which sends out beacon continuously (no scanning).
From the spec, I see that the, 2Mbps is the only feature...
Hi
I am currently developing using GPIOTE, TWI, and TIMER.
There is no problem when TWI is only working, but when interrupt (GPIOTE, TIMER simultaneously) occurs, TWI...
Background : We developing lighting product and planning to use nRF52833 module and we planning to use the latest SDK version that is nRF5 SDK for Mesh v5.0.0. First step...
Hi,
We're doing some testing of mesh protocols and their latencies using the nRF5340 DK. We want to isolate the wireless communication from interference as much as possible...
Our project uses nRF Connect SDK v1.5.0. Two main developers work with the files in very different environments.
I am not sure if this was an accident of initial development...
Hi,
I am currently running a custom bootloader I found that updates via SPI. I have 2 nrf52840 DKs that are programmed as an SPI master and a SPI bootloader. I have been...
After developing with an nRF52 832 DK (pca10040), our code builds and runs fine. But when we try to use the same code on the nRF52840 dongle it does'nt work. We added flashing...
periodic_adv sample is not working with nrf5340dk_nrf5340_cpuapp
it is working for nrf52840dk_nrf52840 after adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf
Here is the log...
My problem is the that on some devices the ScanResult.getDevice() or ScanResult.getScanResult() both return null on some devices but works fine on most.
This is probably...
Hi folks,
I want to calculate the timestamp for which my thingy 52 board was scanning from another thingy 52(may be more than one board). Is there any technique to get the...
I am confirming ADC sampling 420Hz operation by following question.
https://devzone.nordicsemi.com/f/nordic-q-a/69096/1khz-or-more-adc-sampling-rate-over-ble
The source...
Hello,
I am using the nrf9160DK and I am implementing on zephyr.
For my application I need to write to an external flash memory through I2C. I need to write one page at...
