I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
i'm using the sdk only for ble serial data transfer, which i'm not using for this pwm test
all code talks directly to the hw registers
those are some code snippets to...
Hi, There are some older comments. Since situation is changing fast and I am un-sure if these comments are out-dated or not.
ROM size. Some comments said 51 is small...
I'm using nRF connect 2.5 on PC and the latest Android app on a Pixel phone. My firmware is based on SDK 15.1 and soft device 6.1.0. I am using nRF52840-DK boards.
My firmware...
Hi,
I would like to know if the nRF51822 chips come with their own valid IEEE address of if we must buy an OUI and generate our own addresses for use in final products...
Hello,
I propose theses evolutions in nrf_bootloader.c, it allows to use gpregret and gpregret2 for other things:
(nrf_power_gpregret2_get() & BOOTLOADER_DFU_SKIP_CRC...
Hello,
I have questions about Thread protocol:
- Can i ask to network the ID of the last point used to connect a sleeping device ?
- I have a great area to cover so...
I'm trying to develop a beacon application where I dore to read the battery level.
I installed the Segger SES development environment.
If I use the example \examples\ble_peripheral...
I tried to follow the Video on how to use Segger (on this Page. www.nordicsemi.com/.../nRF5-SDK)
for nrF52832, but I get errors when building the Segger Solution: C:\User...
I have an application where I need to be connected as peripheral in 1 connection and as central in up to say 10 connections simultaneously. I posted regarding connection event...
Hi
I've just analyzed a behavior releated to the watchdog and the new SDK 15.1.0 bootloader. The bootloader just reseted after the configured watchdog timeout has elapsed...
Hi,
Currently I'm upgrading our code base to SDK 15. At https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.0.0/migration.html?cp=4_0_1_1_9 there are...
Hello,
I wish to use "ble_nfc_pairing_reference" example with nRF52832 IC and SDK15. I flashed the example into "nRF52 DK" board. When I enable the NFC and BLE on my phone...
Hi,
We have the following problem when start the watchdog from bootloader: the application is started successfully by the bootloader but when enable the softdevice the application...
Hello, I'm implementing a pair of MCUs where one is operating a ANT+/BLE radio stack using the S332 soft device. Whilst TWIS is disabled, we're getting great performance,...
Hi all , I using module NRF52832 and SDKv14 . I have 2 board central and 2 board peripheral . I want to connect each board central to all board peripheral and connect each...
