Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
We are developing a system in which a device controls a host and the device should receive status information about the host. In some use cases multiple hosts are...
Hello everybody !
I am looking to connect 2 cards nRF52 DK (52832) with another card nRF52 DK (52832), a little like the fact my smartphone with these 2 development cards...
Hi, all.
I'm making a mqtt client with nRF52832.
All examples of SDK 14.2 were using PSK secure.
But I want more secured connection as like MBEDTLS_TLS_RSA_WITH_AES_256_CBC_SHA...
Hi,
After sd_ble_gatts_hvx() call, is it possible to change or delete value in softdevice buffer before a connection event ?
Thanks by advance for your help
Best regards...
We have a medical products need to evaluate the maxinum transmission data rate of BLE .i am using is the latest nRF5_SDK_15.0.0_a53641a.
i find to using the ios lightbule...
Dear Developers,
Good Day!!
I want to merge ble_app_att_mtu_throughput & uart example, basically requirement is CLI & other UART communication should work together.
...
See a new landing page on the nordic website for the nRF52840-DK (as opposed to PDK), which states that..
"The nRF52840 replaces the nRF52840 PDK which is not recommended...
We are fine tuning our manufacturing process placing the nRF52840 and would like to know what surface finish is used on the chip. I was not able to find this in the spec.
It seems like a similar IAR debugging problem has been solved but after a day of trying everything...
BLE application with SDK 6.1 and SD 310 1.0 running IAR 8.1 (and identical...
Hi!
Thank you for providing an SDK for BT mesh so early. I'm wondering if you also provide an Android (or perhaps iOS) mobile app that interacts with BT mesh, e.g. by acting...
Hello,
i'm a french student so i'll try to do my best to talk in english with you. I'm trying to use and understand the nRF51822 in order to transmit data to a smartphone...
Hi Expert,
why BLE_APP_UART example can use button 1 to button 4 to wakeup from sleep?
I checked source code I only saw the BTN_ID_WAKEUP is 0.
#define BTN_ID_WAKEUP...
Hi, according to the Bluetooth Mesh Glossary , there are 4 features supported:
1. Relay;
2. Proxy (GATT);
3. Low power;
4. Friend.
Questions:
- Which of these...
We are releasing a firmware update which adds an additional bluetooth profile. Since we do not want or can retest the entire stack, we use a Previously Qualified Design (51744...
