Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I am using the NVS to store my application data in the defined partition starting from a flash address of 0xFC000 to 0x100000.
I have 3 structures with variable sizes...
Interfacing mpu6050 with 52832 DK worked fine .
But when I used same sample code for 5340DK it produced errors .I configured device overlay file as below and build configuration...
Hi! I'm currently working on a project containing an nrf9160 as well as an nrf7002. I found the Nordic Distance Measurement Library, which is very exciting, and I was wondering...
I am currently struggling with the issue of the Bluetooth board disconnecting in irregular intervals ranging from 30 seconds to 10 minutes. The disconnection message is reason...
I kept getting the compile error when trying to build `sample/subsys/fs/fs_sample` ( github.com/.../fs_sample) to `nrf52840dk/nrf52840`.
```
C:/ncs/v2.8.0/zephyr/drivers...
Hi there,
I am working with NCS 2.9.0 and the nRF54L15-DK, running the radio test example with the RSSI Viewer, but it doesn't seem to be working.
Here are some error...
Dear nordic:
There is a problem while debugging the nrf52820 based on ncs v2.6.0
I wanna see the log via debug but failed, the circuitry is as the pic.How I can config...
HI,
We want to use NRF9151 to realize the DECT NR function. Now I have an NRF9151-DK in my hand, how to test the performance of DECT NR?
I used AT command to control NRF9151...
Hi nRF experts.
We built a module using nRF54L15, We are doing some verification. We need to do a distance test, so we need to set the tx power of the interval between advertising...
in my own board. I start a spi master.
and capture the signal of the CSN and SCK.
they looks abnormal
in one burst (package), the CSN has two pulse. I think the CSN...
I'm just using nRF24LE1 to make 2.4G wireless mouse, mouse sensor is PAW3205DB-TJ3T. But i got a problem, PAW3205DB-TJ3T uses two-wire spi(SCKL+SDIO), nRF24LE1 only supports...
I am trying to do an OTA update of the firmware on my device. I am using Nrf Connect SDK 2.1. I followed some of the tutorials and setup the device to advertise the SMP UUID...
I am using the VSCode extension (2024.12.55), nRF Connect SDK ( 2.9.0). I created a new project from the USB loopback sample to investigate how to configure a project for...
Hi,
I suddenly started getting MPSL ASSERT: 112, 2134 upon BT enable and upon research came across this post ( link ) and used following code:
HFXO starts on peripheral_lbs...
Hi,
We are developing a new project using the nRF52832 as our controller and nRF5 SDK 17.0.2 as our SDK.
We have integrated the NUS client and NUS peripheral parts from...
