Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
Hello everyone,
I'm experiencing difficulties flashing my Seeeduino XIAO BLE Sense board using the nRF52840 Development Kit (DK) from Nordic Semiconductor. Despite correct...
Hello All,
I have been trying to get the Xiao BLE Sense with the nrf52840 chip in conjunction with the expansion board to access the SD card using the FatFS example from...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
Hello,
OS: Ubuntu 22.04
SDK version: NCS 2.6.1
Modem firmware version: nrf91x1_v2.0.1
We are evaluating NRF9151 in a new design. We have some prototypes built...
For a project we need to evaluate DECT NR+. We have used the `hello_dect` example ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/dect/dect_phy/hello_dect...
Hello, I'm developing an app that will allow a programmer to flash application firmware and modem firmware. I am able to flash application firmware via JLink Commander. The...
Hi, I had a project which was configured with upto 5 simultaneous connections. Recently moved from NCS 2.4.1 to 2.6.1 and now the advertising stops after one connection. I...
Hi,
I want to DFU the nRF52 from nRF91 over UART. And I find this sample: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/lwm2m_client/fota_external_mcu...
We are working with Zephyr to program the development kit for now and later the real board,
We need access to both UART0 and UART1 but we can't seem to get UART1 to work...
Attempts to build the Matter light bulb same fail for me under these conditions:
A new nRF Connect SDK install on Ubuntu
Toolchain v2.7.0
SDK v2.6.1
VS Code...
Hi,
For Production I need to program by SWD 10 nRF52832 devices simultaneously. The production tools will be prepared for separately connecting 10 SWD interfaces to 10 different...
Hi.
I am experimenting with an internal temperature sensor (TEMP) on an nRF52810 microcontroller and have some questions:
1. How to select a crystal oscillator as a source...
We are developing nRF52840 battery powered device, NCS 2.5.2.
Wanted to use shell for external commands for system testing (currents must be low when the debugger is not...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
