Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi guys , another question here regarding Cmock and opaque types . I am currently trying to mock a function with an argument that contains the type "struct bt _conn " . However...
Hi,
I try to use CPSMS command to reduce the power consumption. The idea is to send a MQTT message every 10min and have the GPS coordinate every 5 min.
The NRF9160 is...
Hello,
I have 3 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to stream left/right audios and I'm able to achieve it.
https://developer...
Hi,
I am investigating low power modes in the nRF9160. I am currently using the GNSS sample code and getting around 36mA. Is there any way to configure the base code to...
Hello,
I have implemented an application for nRF5340 chip derived from the Zephyr AWS IoT MQTT sample. The application is based on W5500 Ethernet driver so the idea is to...
Hi,
I’m trying to have two nrf9161s exchange data back and forth as quickly as possible. Initially the first radio is transmitting, and the other is receiving (3 sub-slots...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. My app configures as BLE Peripheral. Now I want to keep track of the device names of connected...
Hi,
Sorry for the very basic questions. I am new to nRF connect SDK.
I want to develop a ble custom central application with my custom characteristics. I started to look...
Hello!
I have an application using MCUboot and a single application slot. I want to use the Retention System to signal to MCUboot wether to boot normally or into serial...
Hi,
I want to know how to use extended broadcasting in nRF5SDK.
I have tested the Broadcast Multiple of NCS2.6. The maximum extended advertising data length is 31 to 1651...
Hi! I am beginning development on my first BLE project using nRF Connect SDK in VSCode. I have done a few projects using the old nRF5 SDK. I am wondering what is the best...
Using VS Code, I've tried to build the "BLE UART service" (= peripheral_uart) for the nrf52840dk_nrf52840 board. According to the documentation, this board is supposed to...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
I am implementing firmware to communicate using UDP between two nRF7002.
The sender does not know the IP address, so it tries to know the IP address of the receiver...
