I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I am using this SDK version 17.1.0 as I am using ESB in this project. So far I have gotten ESB, SPI, and UART communications working. SPI and UART are both using easy DMA...
Running on Fanstel BM15M module (nrf54L15) SDK v3.1.1, I seeing a huge timing error when trying to implement a simple timer function. In the code below, I believe I have followed...
Hello,
Caught this Nordic Skydio presentation by chance this morning and briefly mentioned was the use of a dual core processor mcu. Was this the nrf5340 or some other Nordic...
When evaluating the hardware performance, we tested the WiFi speed of the nrf54lm20 + nrf7002EB2.However, the test result was only 2MB per second.I suspect there might be...
I would like to check if our observation with nPM1300's VBAT node is expected per the IC's design.
As a background, in our application ee use a low-leakage switch to isolate...
Hi,
we have made a pull request on github to introduce the LTI support in CTS client, since one of our new devices have a display and needed a user friendly way of supporting...
Hi every one,
If any body have been succeeded in adding DFU support in Fast pair locator tag on nRF52833-DK, if so can you guide me for it?
I am getting configuration...
Hi! I am using nrf connect sdk 2.6.1 and modem firmware 1.3.7 on a nrf9160. I have an application where i need to try to get a fix on a set interval and also sometimes transmit...
Hello,
I am working with NRF52840 dongle.
I built and downloaded the hid-keyboard example to the dongle. HID keyboard function looks good that a "1" is typed by pressing...
Hello Team,
I am using SDK version 17.0.1 and have implemented OTA. I have also implemented a buttonless DFU without bonding and created a Blinky application. However, when...
Hello,
We are also having trouble installing any SDK into the VS Code Ext Pack, for development on the nRF54L15-DK. Have tried each SDK from 3.0.0 to 3.2.1 without success...
Hello,
I have a functional project to access to an SD Card with NRF54L15DK and the version 2.9.2 SDK and 3.1.0 toolchain.
But I have difficulties to access to the SD card...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Dear all,
i have a problem when i compile a project with Segger v. 8.22a (but i tried also with v.8.26) .
The message is:
Linking 'ne_eere.elf' Linking ' ne_eere .elf...
