I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Custom board using BL654 (NRF52840)
SDK 17.1.0
SD140 7.2.0
I was able to run the ble_app_uart totally successfully (with RTT LOG output) until I tried to add uart capability...
Hi,
What would be the best orientationg for data acquisition with the Thingy's 53 microphone? I see the plastic case has some slots.. Those up or down? Outwards or inwards...
Hi,
In the documentation of SDK 17.1.0 it is stated that only s132 v7.2.0 is supported. I want to update from SDK 16 to 17, but don't want to update softdevice, currently...
Using the nRF9160-DK together with the Power Profiler Kit 2, I observe sometimes a longer period (1 minute) of a 50mA consumption before entering PSM mode.
Is there a explanation...
Hi,
Our application has a GUI, the UI data is stored in the QSPI flash and it is independent of the firmware,
We program the QPSI flash via the PC tool in the development...
Hi , I got my Nordic Thingy : 53 I wanted to connect other sensors to the Stemma/qwiic port of it . Can you share some documents or example of how to connect multiple sensors...
Hello, I have a problem regarding production flashing a nRF52811 device. We are using a Segger Flasher Compact, but I also tried a Segger J-Link Compact. To flash we are using...
We used 52840 chip to produce a near field communication module, the antenna is on board antenna, some problems occurred during the verification process, can your engineer...
hello Nordic
i work on nrf52832, trying to run it with zephyr application
one board runs fine (more/less, there are some MPU FAULT issue that i am facing with no luck...
Hi everyone,
I have some issue when my device is in very low temperature of -60°C / -70°C.
We use an NRF52832 (SDK 15) on modules (BMD-300 frome UBLOX formely RIGADO...
I'm working with lsm6ds33 sensor using lsm6ds3 driver I get some results, but they are ae rarely modified and didn't follow the IMU motion so how can I correct this.
(The...
Hello,
When I use sntp to get the timestamp from time3.google.com, getaddrinfo returns a -10 error. nrf9160 device also reboots automatically, why did the device reboot...
Power Profiler app v3.5.0 running in nRF Connect for Desktop v3.12.0 in Ubuntu 220.4 reports "No Supported Devices Connected".
I have used my PPK2 successfully recently...
Hello team,
I was not able to receive a suitable reply for this post for almost two weeks. I started thinking the engineer had gone for vacation. That is the reason I...
