I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am using nRF connect SDK V2.0.2 chipset 52832 built using VS code.
Need to move the setup from an external clock to an internal RC oscillator.
When I disable ...
The following Pin definitions for QSPI result in Errors during build using NRF Connect SDK. This exact configuration is working on a custom design using nRF5 SDK using the...
I want my client to advertise forever so I added the following code:
static void ble_evt_dispatch(ble_evt_t * p_ble_evt)
{
ble_conn_params_on_ble_evt(p_ble_evt);
ble_nus_on_ble_evt...
Hi,
My device was designed with SDK 15.0, the APP_ADV_DURATION is set to 0 in order to have the device in advertising for all time.
Now I try to use the SDK 15.3 but when...
I've got an embedded application where I want to stream from my device to wireless headphones. Really looking for legacy (I think) right now as I'm not sure LE audio is supported...
I'm getting an occasional MPU fault on the nRF52840 on the Thingy91 when starting scanning:
Running arm-none-eabi-addr2line leads me to
buf->len -= len;
in...
Hi,
I am working on PWM and i am using bellow function for pin set cycles and it's working fine as per Duty cycle and frequency
i am getting the wave form also but i'm...
Hi All,
Is macro in /modules/nrfx/hal/nrf_rtc.h correct?
/** @brief Macro for converting expected frequency to prescaler setting. */
#define RTC_FREQ_TO_PRESCALER...
When compiling without a pm_static.yml in my project and using the dynamic partition resolver with mcuboot I noticed that I get an overflow error.
The current accepted fix...
hello
I am using ufl(U.FL-R-SMT(01)) 50 ohm antenna
My question is: is the matching circuit listed in the picture sufficient or do I need another component
Hi community,
For debugging / a project in very early stage I need to sniff Thread packages and (later on) Bluetooth (LE) and ZigBee packages.
I would like to use the...
After reviewing the add DFU support to your application guide
i have several questions:
1)What modifications are required for the nRF5340 with an app core and net...
We are using SDK15.0.0 and have products with both the NRF52832 and NRF52840 sharing the vast majority of code between them. The softdevices we use are S132 and S140 at version...
