Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
my project requires a simultaneously data-collection from 13 IMUs sensors which we built with NRF51822 + BNO055 (IMU)
we used the Gazelle mode, I understand each host can...
Hi,
I was checking the nRF5 SDK getting started series video - SEGGER Embedded Studio - Importing files and drivers .and the PWM driver SDK directory structure is updated...
Hello,
I try to connect a BLE application with my PC by using an nRF52840 dongle and the PC-BLE driver. But I got stuck in the understanding of the driver, so I hope that...
Hi,
we are having issue with nRF52832 and littlefs. We are using Nordic Connect SDK 1.9.1 and Visual Studio Code.
We created dts overlay and removed partitions not needed...
Hi,
I'm using GPIO pin as input button with nrf9160 using Zephyr RTOS, but when I was press the button I didn't get any response from button state.
hear is my code
...
My query is:
1. Is it possible to access the azure using WIFI network in above application?
2. After knowing the IMEI using AT Command, in response to which event should...
I am getting more current consumption when internal pull up resistors of nRF52832 are disabled and external pull up resistors of the slave sensor are enabled as compared with...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi,
I saw in ozone that SW crashed with hard fault explained as escalation of exception that was not enabled.
How can I enable all exceptions to see the exact reason of...
Hello, I'm using nrf52833, pca10100.
My project is based on 'ble_app_uart', and I added buttonless DFU project.
this is ble_dfu_buttonless_async_svci_init() function...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i cannot seem to select nRF Connect SDK when creating application in vs code. i already install the nRF Connect SDK v2.0.0 from the toolchain and the nRF Connect Toolchain...
I am trying to build a example program in KEIL for the nRF52832 QFAA device. When I sart KEIL the program shows a massage that says the nRF_DeviceFamilyPack.8.3.1 is required...
Good day to all I am trying to change the Application on a device with an nRF52832 chip with an existing firmware. To do this, I use nRF Connect for Mobile 4.25.3. From the...
