I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
HI
I am currently using nRF54L15 with NCS 3.0.0 SDK, running the periodic_adv_conn example. I made the following modifications to the extended advertising and periodic advertising...
I am porting nRF SDK 2.6.1 to SDK 2.7.0 on the nRF5340. For the network core, where exactly should the kconfig (prj.conf) file be located and named? On the sysbuild migration...
Hi, based on the previous struggle with data transfer drops with nrf9161 ( ) we came after the cooperation with Vodafone MNO to the situation, that (at certain test place...
I'm using the peripheral_bms project. The only change being in the overlay to make it work with nrf52833 dk. I'm able to connect with nrfConnect and see the services (except...
I'm developing with the NRF52840 using IAR Embedded Workbench , and implementing wireless communication based on the IEEE802.15.4 Zigbee protocol .
In the MAC frame layer...
I am new to Nordic and want to design with the nRF52840. I have read this guide:
used AppCAD to find the best width and clearance for the ground layer, but when I downloaded...
Hello, I am using NCS 3.0.2 on nRF52840. I have been using MCUBoot for a long time on my device, and it is working fine. Recently, I went through a requirement where I needed...
Hey everyone,
I've been trying to get the Bluetooth Mesh DFU Target sample working on my nRF5340 DK and running into some issues. I've read through the docs.nordicsemi.com...
Hi All,
I have an nRF5340 Audio DK which has problem with the network core. When I connect the USB to board or try to recover the board the MCU light at the bottom of...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's and I want to have the same functionality of the walkie talkie demo but instead use the microphone of the...
I had a working Matter application, but due to some human error, I erased my WSL installation.
I set it up again, but after successfully flashing my code onto the Nordic...
Hi,
For a product currently under development, we need to use a counter as an RTC. We’re targeting the following commit in ncs/sdk-zephyr :
github.com/.../d7e41fd2e361ee15454a253ebec9bb37aceaf09f...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
