I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
Is there a low power consumption for battery powered long term (months) application for Nordic Thingy 91? I don´t need GPS position, just to receive sensor data and...
Hello
Using a Thingi91 with latest firmware and Asset Tracker v2. Connects to the tower, but cant seem to connect to the NRF Cloud. How can I check if it can reach any other...
Hello all
I am using the Thingi:91 in Sri Lanka. I can connect to the tower correctly, but cant get data connectivity yet. I am told by the operator that they use the following...
On nRF cloud I registered the ibasis sim card which came with the 9160DK and connected it to that 9160DK device. I'm now using a Fanstel BLG840F and wanted to know if the...
hello Nordic
i am using nrf52840, with zephyr
i wish to use the nrfConnect Tx power service to read and to SET my Tx power
but in ncs in zephyr/subsys/bluetooth/services...
Hi,
I am using nordic52840 dk board.
And i want to flash a bin file using nrfjprog command line.
For Hex file i am using below command
nrfjprog --reset --program blinky_pca10056...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
nRF5 SDK > nRF5 SDK v15.0.0 > User Guides > Developing for nRF52810 gives a list of things to do to adapt an nRF528 32 project to an nRF528 10 target.
But, looking at...
Long story short.
I am trying to merge DFU master code to feed a DFU.zip to the DFU receiver code already present in the secure bootloaders (but elevated successfully into...
I'm working with firmware and hardware that has previously worked properly. I recently migrated to S113 from S140, and changed the data format of what was being set in the...
I am trying to create my first Freestanding Application under NRF Connect, I have SDK version 1.8.0. As soon as I click on "Create Application" I got the error message " Application...
Hi,
I am looking for the sample code of Class B type LoRaWAN end node for Zephyr platform. I am using ncs 1.8.0. I am able to find sample for Class A end node at v1.8...
