Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
What is the difference between the Async Read ApI and the Normal Read API of the ADC ?How the ASYNC read API work ,can anybody explain with sample code. Specially thirds argument...
Hi, We have designed a custom board using nRF52840 SoC, now we want to calculate its power consumption I want to ask if we can measure custom board power consumption using...
I am trying to use the NRF52832 to connect to the BMA456 Accelerometer from Bosch using SPI and am running into the following issue:
All read/write commands work fine...
Hi, I'm trying to implement a timer that will trigger each 10ms (for example) an handler function and do something inside it. So, I came with the idea to implement an App...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
Hello Everybody,
If you're reading this, you're likely in the same boat as me and need to scale Nordic's build process in an environment that doesn't have access to west...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
