Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I’m trying to run **LVGL 9.3** on a **nRF52840 DK** with a **2.8" ILI9341 TFT display (SPI)** using **NCS v3.1.0 / Zephyr 4.1 / Toolchain v3.1.0** .
### Problem...
Hello, I want to check the component alignment on the layout.
My layout is different than the reference.
Where should I connect the VNA?
Can I calibrate it on the PCB?
Hi,
I am using a custom nRF9160 board with the nRF7002 Wi-Fi chip via SPI, running NCS v2.9.2 . My goal is to connect to a Wi-Fi network.
However, during initialization...
I want to change the start address of the app in the ESB example from nCS 3.0.2. By default, after compiling and flashing, the program runs from address 0x0. I want to change...
Hi Nordic,
I try to print hello world from promicro(nrf52840).
I am sure board is ok, because I test zephyr 4.2 cdc_acm example on it, and I can see /dev/ttyACM* & console...
Previously, when our NRF5340 was transmitting at a 3ms interval, we encountered issues where the transmission speed failed to meet requirements, with data packets being discontinuous...
Hi Team I was exploring communication with ads1292 over SPI at 1 MHZ. I tried nrf_drv_spi (SPI0_ENABLED in sdk_config.h) api and I was able to communicate with ads1292, however...
I try to do everything as in the guide (second advanced option) devzone.nordicsemi.com/.../small-i2c-oled-displays-using-nrf-connect-sdk but I get errors when building
...
I need to set the connection interval to 7.5 ms. The main.c has the corresponding macro: MIN_CONN_INTERVAL but it seems to me that it supports only integer values...
Please...
When building examples targeting the thingy53/nrf5340/cpuapp board target cmake is run twice, on a fresh build. Then once the build is finished, without modifying anything...
Hi,
In the past we had quite some issues with moist in nRF9160 issues (likely due to bad storage at our PCBA partner). We are now baking all nRF9160 always at 125 degree...
Hi all,
i am currently developing applications for the nrf54L15 for science. We ordered nrf54L15DK and everything is running fine. As we would like to switch to public availabe...
Hi,The Nordic Team
I am developing the Matter over Thread product. I have defined a Bluetooth transport protocol, and now I can receive data. But now I do not know how to...
Hello Nordic Team,
I’m looking to build on a BLE Scanner(Beacon functionality) + Peripheral features on my application using the nRF52810 device, but I’m facing difficulties...
I've been unable to get a SPI MOSI pin to output data on nRF54L15DK using Nordic Connect SDK v3.0.2. SPI transactions report success, and the SCL and CS lines are clocking...
