I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi there,
How can I manually awake my advertiser which is in low power mode, to start advertising and get it back to sleep after it advertises certain number of packets...
Hi,
I'm having some troubles with the Thingy:91 because it became unresponsive after I flashed the device with the mqtt_sample firmware.
I built the mqtt_sample with...
Hello everyone,
I am having an odd problem. I am using an SoC based on the nRF52832 (the ISP1507-AX). So far I had been using ncs v1.6.0-rc2 during development. Recently...
hi support team，
customer have one question, when 9160 attach the network, which one does it choose (the best signal or the first base tower discovered)?
especially when...
Hi Dev Team,
I am developing the weight scale product using nrf52840 development board. We connected the nrf52840 using the nrf connect app ( Provided by nordic).
Now...
Hi, I'm using the BC805M EK (nRF52805) . I would like to pull up pin 20. Here is my configuration in pca10040.h. However, pin20 cannot be pulled up. It's always pulled down...
Hello Devzone Community,
I am trying to develop an nRF9160 firmware, based on Nordic's sdk-nrf v1.6.1 code base. This work is a Zephyr RTOS based application. In early research...
Hi, I would like to know all of my possible options for improving the communication range between 2 nodes in ble mesh. I am working with the nrf5 17.0.2 SDK and the nrf5 SDK...
Hi everyone,
Explaning my project: an external device transmit via UART to nordik nrf52840DK device with UART peripheal firmware, this is connected to another nrf52840DK...
I'm testing the http functionality. In my code I test against 2 different servers, one plain http port 80 "postman-echo.com/post" The second server is private https server...
We are using NRF52832 with STM32L4A6 using serialization. We have the serialization working properly, but having an issue with the MAX MTU size. We can set the NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hi, I recently started working with Segger on nRF52832 . It is possible for me to initialize BLE advertising but I am having problems in initializing a custom service. I ...
Hi,
I am currently working on a project that uses the nRF52840 MCU implemented with the nRF5 SDK and nRF Bluetooth mesh. In our future plans, we want to use direction...
