I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm currently trying to send a HTTP body payload that includes "\r\n" in the data payload. I'm getting an "OK" response before I have sent the complete payload.
The problem...
Hi,
I use the nRF52832 with SDK14 and no softdevice.
The MISO on oscilloscope is correct but value in the receive buffer is wrong (can be any value). Unfortunately...
Hello,
Sometimes we don't get a fix when seeing 6 satellites with highest 27dB and lowest 18dB signal strength. And sometimes we are able to get a fix with a GPS fix even...
Hello,
I use NRF52832 with SDK 17.0.2.
I run app timer and pwm driver independently ok.
I merged App timer with PWM Driver. But only PWM run, I can't make app timer...
Hi There,
Now, I want to supply energy on the board with external power. As to say, I cannot supply power on the board by USB. In this condition, can I connect the board...
Hello,
Im New to Nrf51822 im trying with Nrf51822 dfu bootloader dual and single in sdk51 . But after compiling the ble not showing in Nrf connect at all. Whats the IROM...
In BLE Central Example like HRS and RSCS,
Central has Enabled the notification when event handler find Case : BLE_RSCS/HRS_C_EVT_DISCOVERY_COMPLETE.
But what if we want...
Hi,
I am working with ppg sensor to calculate heart rate and spo2. I collected data and printed it on RTT for first cycle values are printing on RTT. But after collecting...
When I debug the twi_scanner_pca example , it gets stuck at .thumb_func .weak HardFault_Handler HardFault_Handler: b . On my NRF DK2 everything is fine, on my rigado eval...
Hi, I am trying to compile and run the ble-pc-driver tests but am struggling.
My best guess based on the documentation is that I am specifying something wrong when configuring...
Hi,
I am performing some evaluation on the low power capabilities of the nRF5340 using the DK and the PPK v1.
I have written a really basic BLE Peripheral Application...
Hello,
Currently I am connecting between nrf51822 and Rn4871 BLE of Microchip
The issue is that Rn4871 is advertising a service called transparent UART UUID : 49535343...
Hi Nordic
We are working on nRF9160 DK for our LTE+GPS product development.
We are looking for FOTA and BLE OTA Update for our board.
Is it possible to do FOTA update...
I am quite new with nordic environment .
My application is to start 2 pwm instance in opposite polarity (i.e 1 high polarity and another is low polarity with same duty cycle...
Hi,
During bluetooth DFU
I want to generate the file 'setting.hex' in the folder through 'app.hex', and burn the four files in the folder 'bootloader.hex' and...
