I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
i am using "ble_app_uart" example code in nrf SDK to connect to bluetooth and to read-write the data after connection through nrf connect application.
write...
We are using a custom board with softdevice S132, sdk14, and freertos and ana nrf52832.
Our ble_app does:
init gpio put up a splash screen via a display on spi
...
I am starting a new project using SDK 17.0.2, DK52 dev board and Segger embedded Studio.
To create the new project I started from ble_app_buttonless_dfu and commented out...
I got the update notice for 3.6.1, the install gets to around 33% then just sits there. This happens both with upgrade and with clean install for me, I left it to hang for...
Hi all,
in my current platform I have:
a DK (we are working to implement HW modifications to use a nrf52 dongle for this purpose) that is performing as a Thread DFU...
Hello,
I am currently trying out the assert mechanism of Zephyr.
I have added CONFIG_ASSERT=y to my prj.conf file and included " sys/__assert.h " in my main.c .
My program...
Hi,
May I ask what's the minimum reference circuitry for running nrf52840 without RF? Thanks.
My scenario is as follows.
1) RF, eg, Antenna is not needed
2) GPIOTE...
Hi,
I'm developing a CENTRAL using 52832 to connect a earphone.
1.When I enable LESC, the pair fails with the AUTH_NOT_SUPP error. Why ?
What I think if the earphone...
Hi.
I'm trying to use direct advertising to connect only with devices that have already been paired.
When I start direct advertising, I get a app_error_fault_handler...
Hello,
I am using nrf52832 and I just have 3 questions regarding it.
1) SAADC change over temperature. According to the datasheet, it has a change of 0.02%/C but I only...
Short version: can I use a pin both as a GPIO input to trigger GPIOTE PPI event, and as SPI MISO *at the same time*?
Detailed version:
I want to use the SPI peripheral...
Hello everyone. I want to turn the LED on and off with the push button, if I want to hold it down after 3 seconds the LED will turn off, if it has been pressed for less than...
Hello
I am trying to port a custom project for nRF52840 from Keil to Segger Embedded Studio -uVision V5.33.0.0 -Armcc V5.06 update 7 (960) -SDK 15.2.0 -Device Familly...
