I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello,
I'm trying to create a long range IAS ( Immediate Alert Service ) unsing long range BLE 5.
On the server software I forced the PHY to BLE_GAP_PHY_CODED. I saw in...
The 'Debug Out' on nRF52832 (and 52840?) Dev Kits only works at 3V - so won't work with a 1.8V target.
The question has been asked before, and the obvious answer given ...
hi,...
i am using nrf52382 and nrf52840 ... one is client and server . i am using mesh sdk 3.1 .... i have debugged the example light switch server and client respectively...
Hey
This is sumanth. I have worked on mesh beaconing example and saw the output of continuous scanning advertisement of nearby devices in RTT, I made changes in light_switch_server...
I need to configure 1 device as relay node in order to relay messages from the client node to the server node. To test that the sever is relaying messages i could lower the...
Hello and thanks for your help,
We are looking forward to build a low cost and power wireless application using 802.15.4. We do not need any other protocols.
Am i right...
We have an NRF52 set up as Central, connecting to a peripheral (not our own) that's sending notifications with Data>20 bytes
I'm trying to differentiate between it sending...
Hello everyone,
I'm trying to set up entirely open source project for my NRF51822 chip. Everything works fine so far but something strange happens during debugging.
I...
Hello support team,
I am using your product through a module vendor and I have a question regarding errata 197. If the DC/DC regulator only has problems in low power states...
hi... i am using nrf52840 and nrf52832..... mesh sdk 3.1 latest version ....
in this case i am using client as nrf540 and server as nr52832 .... i have debugged the light...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
