Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello
I am using Segger Embedded Studio with nrf9160. I can 'Build and Run' the 'asset_tracker' project but the LEDs are not blinking and my development kit is not connecting...
Is possible to get a sample code for communication between multiple BLE devices, for example the BLE TinyShield? I have come across a code that enables the BLE TinyShield...
The content, format, and size of a device's Peer Data is determined by the application. I understand that when pm_peer_data_store() and there is not enough available flash...
Hello there,
In order to have a continuous RTT debug during DFU, I followed advices found in:
- https://devzone.nordicsemi.com/f/nordic-q-a/20708/rtt-logging-from-application...
Hi,
Apologies if this has been asked before. I am interested in trying out the Adafruit arduino implementation for the NRF52840. The implementation uses it's own bootloader...
Hello,
Que 1:I want to Test BLE APP UART Functionality with BLE MESH Example ..is there any document how to use Combine BLE and BLE MESH?
Que2: I want to run BLE MESH...
Hello everyone,
I would like to know, if the nRF9160 module can operate using a supply voltage which ranges from 2V to 2.2V.
Furthermore, Can I install a different SIM...
