I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm trying to read a voltage from my power supply using the differential SAADC on my board to simulate the readings from a thermopile that I ordered so I can start calibrating...
Hello,
I am working with nrf51822 and I want to send data over ble to an android application which requires pairing. I modified the ble_app_uart example to read the data...
Hi Nordic Forum!
We're currently tuning our antenna since we runed with some problems during our EMC testing.
In that regard, what is the impedance (both input and output...
Hi,
Is there no specific code of ble_app_uart_coexist meant for PCA 10056 and eventually s140?
Or will the same code work for the nRF52840 board?
I am using SES and...
I want to use the nordic USB peripheral drivers to allow for the initialization of multiple devices. The end result of the project will be to have a single nordic creating...
I am using the nRF52832 (on Rigado BMD-300 EVAL kit). I am using keil IDE and nRF GO to upload my compiled code to my device. I am using SKD 15.2.0. Using Windows 10.
...
i donot know why,because other board is ok.
i am using this project
\nRF52832 pack\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c...
I am migrating my project from SDK 15.0 to SDK 15.2. I was using CC310 to accelerate crypto in the bootloader.
While builiding the bootloader wit SDK 15.2, I got the error...
Hi team, Does the nordic chip receive a Bluetooth signal being communicated with a mouse, keyboard, cell phone, etc., and the sleep state (sd_app_evt_wait()) is canceled?...
Hi,
Can we use BLE 5 beacon with BLE 4 scanner?
As BLE 5 is long range which is my main concern. So, can I get that long range with BLE 4 scanner?
Thanks,
i have done the 10 dfu steps in DFU quick start guide when the boards are not far from each other it works but when i make them far a little
i mean one device in the area...
I am using a Sparkfun nRF52832 breakout. I was trying to install the Softdevice settings onto my Arduino IDE once I clicked on tools -> "nRF5 flash device " the blue ticking...
Current consumption of my code running RTC from LFCLK is ~2.5uA from the power profiler when I set the register values as. NRF_POWER->RAM[2].POWERCLR = 0x01; NRF_POWER->RAM...
Hi,
Currently evaluating SDK and have some issues, I would like to run some demos.
I believe I've managed to erase the "preconfigured" Firmware on the SDK, I have tried...
