If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hello, everybody.
I'm working on combining the nRF52840 and the GPS module and are currently developing a program that stores real-time GPS data in an external flash memory...
Hi,
We are planning on upgrading the firmware on our device from Mesh v0.9.2 to Mesh v3.0.0 via BLE.
Specifically, our current stack uses: - nRF5 SDK for Mesh v0.9.2 ...
IPhoneX sometimes goes into the ble_evt_handler auth_status event, and then p_ble_evt->evt.gap_evt.params. Auth_status.auth_status!= BLE_GAP_SEC_STATUS_SUCCESS, other iPhone...
I am unable to compile any SDK12 example with SES even following the tutorials. Versions in tutorials are different from those actually available resulting that menus shown...
What is the difference between the twi_sensor example and the twi_master_using_app_twi example? Where do I find any documentation that describes the available functions for...
Hi
we are currently designing a device using the nRF52840 and are looking for information on the most cost effective way to do large scale production testing.
will we...
Hi,
I have an issue with pinging the nrf52 (PCA10040)(with mqtt_pub loaded), from the PC on the LAN to which the Raspberry Pi is connected to.
I can ping the nrf52 from...
Hi, I've followed the tutorial on https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . I got to the end of the tutorial...
Hi,
In your reference design: https://www.nordicsemi.com/DocLib/Content/Product_Spec/nRF52840/latest/ref_circuitry?1070#unique_1780233596
There is a line from DEC2 to...
When I debug my product ,using nrf51822, using the ble_uart example, my product will using MCU commnication with BLE,using uart.
When I modify the PIN of the uart TX pin...
Hello:
I am working with my sales contact at AT&T in the USA. I mentioned this module and that it was going through certification. Before I moved forward with the carrier...
Hi,
I'm using an nRF52840 dongle with pc-ble-driver on Linux. It has connectivity 6.0.0 with S140. I tried the heart rate collector/monitor example pair (I have two dongles...
Hi folks,
We are in the process of evaluating nordic chips for our product.
One of the features we need is the ability to record an audio sound from an Ios app, send it...
Hello,
I have got nrf Power Profiler Kit for power consumption testing in our application board. I have a question regarding its output voltage for DUT devices. My application...
The project I am working on is to store the data acquired through BLE_uart_c and the data collected by the sensor on SDCard. I use FreeRTOS. The problem is described as follows...
