I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
can I use an nRF52840 based BLE gateway? Backhaul would be either 10/100 Ethernet (via Wiznet or Microchip controller chip) or a cellular module. Is the clock speed sufficient...
I am unable to get 6 notifications per connection event. I am connecting two nrf32832's, one as a central, one as a peripheral. To make this as simple as possible, I limited...
Hi
We are able to provision several mesh-servers.
The log on the RTT-Viewer of the client looks normal:
0> <t: 915394>, mesh.c, 178, Local provisioning link established...
I am working with the peripheral/flash_fds in SDK14. I need to adapt it to use RTT instead of uart
I have made the obvious changes to switch from uart to RTT, eg substituting...
Hi everybody,
I'm trying to use the example ble_app_hrs with s110 on the PCA10001 Board and the ble_app_hrs_c with s120 also on an other PCA10001.
I changed some led flag...
I have already explored how to fix the related problem in the DevZone. I think the firmware of the ATSAM3U2CA-AU is erased. Here, I have two problems:
1, How can I get the...
Hi,
According to the code in PCA10059.h:
#define RX_PIN_NUMBER 11 #define TX_PIN_NUMBER 9
I would like to know what pins are related to number 9 and 11 in this schematic...
Hello,everyone.
If you have some suggestions,and you leave them, I would appreciate it very much.
I designed a pcb base on nRF51822. It can only be searched by mobile...
Dear Nordic support,
I am working on a device based on the FreeRTOS heart rate example and I am having difficulties with the BLE connection when connecting to iPhone X...
Hi, I want to reduce current my module.
I used SDK15.0.0ver, nRF52832
I have 2 questions.
1. I used app_uart_close();
But My module was reset again.
2. I want to...
hi...
i want to check my data for every minute , so i set the timer for one minute.
but its not working ....... how to do?
i have set the timer like below
i am finding...
Hello nordic team, I have a question regarding BLE Mesh and Uart0:
The InfoCenter is saying that Uart0 is blocked when using the serial Support. I don't wan't to use the...
Hi,
I'm testing an interactive pyaci example in Mesh SDK v2.2.0 with two nRF52DK boards.
Interactive mesh provisioning and configuration example worked fine so I modified...
