I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
Hi,
I have a Zephyr ZigBee project based on the Nordic Light Bulb example and a custom ZigBee2MQTT integration. However, I can not trigger an identification on ZigBee2MQTT...
I am using the nRF52840, which has BLE support but does not have a touch sensor. Can you recommend a module that includes both a touch sensor and Bluetooth?
I'm now trying to test dongle on nrf52840dongle board：
1. west build -b nrf52840dongle_nrf52840 -- -DCONF_FILE=prj_4llpmconn.conf
2. open nRF Connect for Desktop's Programmer...
hi
board : nrf52840dk
sdk : nrf connect sdk v2.6.1
example: matter light bulb
problem:
I want to add another set of PWM to the sample code. How should I configure...
The docu page for the nRF9151
https://docs.nordicsemi.com/bundle/ps_nrf9151/page/ip/radio_lte/doc/frontpage.html
contains a link to
docs.nordicsemi.com/.../intro_nrf9160...
I have customed my own 52820 dongle board.
I wanted to run ncs2.7.0/zephyr/samples/subsys/usb/cdc_acm demo on my board to test whether it worked. So, I builit the cdc_acm...
Hi
I'm trying to make the UART-HCI example run on my nRF5340-DK board.
Environment: - nRF5340-DK Version 2.0.0 (2022.13) - nRFConnect 2.7.0
I've built the example with...
