Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi all,
We have an application which uses both MCUboot and a watchdog timer. This combination seems to be causing issues anytime we attempt a soft reset using sys_reboot...
Hello Team,
I have have loaded the modem FW 2.0.1 and Serial LTE Modem application on my NRF9151-DK from Quick Start. I wanted to test the RAI release functionality and...
Hi,
If the image we falshed using mcumgr is 90% of the allowed image size mcumgr flashes the unit without a problem, If the image is 98% the proccess seems stuck.
...
I am receiving bytes from a GPS module and passing them to BLE UART example app configured to use UARTE1 and asynchronous API.
After few minutes of running it starts leaking...
Hello everyone, I have two nrf5340 kits. I run "Bluetooth Direction Connectionless" applications with these kits. I also have a CoreHW brand AoA antenna. My question to you...
Hi, I have a custom board running with the nrf9160. It also has the npm1300. I have it set up so that it is configuring the pmic and then turns off the cell and goes to sleep...
Hi
Can we use nrd52840dk as bluetooth(for data transmission to user created mobile app) and to calculate distance using multi carrier phase difference method between itself...
We are having an issue with
This happens to us because we are using the NRF carrier library, and in the carrier library, when you are trying to power off the modem,...
Hi, I'm coding a nrf55832, my code uses TWI, UART, SPI, app_timer, nrf_drv_timer. The code was going welle until i add the saadc. When i call the nrf_drv_saadc_init function...
Dear Nordic Engineers
I used gd25lq32e to replace mx25r6435 and it is a 32Mbit Flash, when I add it to the Devicetree of Lwmwm(NCS 2.6.1), the build will report the following...
I'm currently working on a POC for the nRF9160 with an external host processor. I have the Serial LTE Modem example running on the nRF9160 and have the serial comms between...
Hi,
I have a simple question ... I think.
I have been limiting my USBD reads/writes to 64 bytes as NRFX_USBD_EPSIZE and NRF_DRV_USBD_EPSIZE are set to 64 bytes. I have...
Hi all,
I am using the nRF5340 DK. I am trying to run the ncs/nrf/samples/openthread/cli sample with no changes. I have tested this in both ncs v2.7.0 and v2.6.2. I am able...
