Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
I'm looking for the quiescent current and efficiency of REG0 DCDC under the conditions of 3.0v ≤ VDDH ≤ 4.2v, VDD=1.8v.
This is to determine if external regulation using...
I have a SparkFun Pro nRF52840 Mini that I am trying to flash with a simple Hello World program. I have the SDK setup in Visual Studios, created the custom board configuration...
I have this code developed for nRF5340.
Basically it scans for BLE advertisements based on the filters added and transmits the packets through UART.
Now for certain reasons...
Datasheet sampling rate is 100Ksps, but for me PPK2 always returns:
16384 bytes in ppk2_test.get_data() (one sample period)
4096 analog samples in ppk2_test.get_samples...
Hello Nordic,
I want to power down (at the lowest power consumption state as possible) all the peripherlas.
Already checked below ticket.
Below ticket also referenced...
hi,
I use softdevice s140 and nrf5_sdk_17.1.
I import time sync demo from here ( github.com/.../nRF5-ble-timesync-demo) to my project.
My first usage version:
* nrf52...
Hello,
I’m encountering an issue with my nRF52 device where it reboots during the flash_erase operation. Below is the relevant part of my code and the overlay configuration...
Hello all,
I'm using nrfx_spim_spis non_blocking sample to make my nRF5340 DK as SPI SLAVE.
I don't need SPI MASTER, so I delete the SPIM code.
But I found that I can...
Hi,
Is there any relationship between RTC peripheral and the system clock (which from DTC it looks like attached to rtc0)?
I'm trying to use PPI to generate a radio task...
I am looking for a solution of a multi-protocol controller for Linux host.
1. Coexistence of Wifi & BLE & Thread / Zigbee
The ble-coex / thread-coex example has the...
I'm trying to do a power analysis of an embedded device with a PPK2 and nRF power profiler and i'm running into an issue where i'm losing samples on longer capture periods...
I have a simple Thread joiner program. I am trying to join to a thread network created by my OTBR. Attached is my program. This program resets on call to otJoinerStart()....
Hi,
We use SDK 2.5.2 on a nrf9160. And have a hardware issue due to a too late update with the first boards. The GNSS LNA enable is wrongly connected to COEX1.
COEX0 is...
We are using eDRX to save power, but it seems like eDRX is not active always.
We currently use LTE_LC_EVT_EDRX_UPDATE callback to determine if eDRX is active. Is this...
