Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I am trying to implement bonding in central BLE uart_app example code but I don't know how to proceed as I'm a beginner . Do we need to make any changes at peripheral side...
Hello Nordic team!
I'm following this tutorial from Nordic to do DFU OTA: https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/getting...
I am following this post regarding reading the static MAC address for the nRF52840: https://devzone.nordicsemi.com/f/nordic-q-a/68376/trying-to-extract-the-static-mac-address...
Hi, we have a device that reads two sensors on separate i2c buses consecutively and transmits these using ble_nus_data_send().
The i2c sensors are read on an interrupt timer...
Hello all,
I am moving from the Arduino Uno to the nRF52 DK on Segger. A big difference
When looking at the examples, I cannot see the so-called setup() method, so, I...
Dear Forum,
I have the following issue (my System: Ubuntu 20.04):
I created the secure bootloader with Softdevice S140 (v.7.2.0) for 52833 chipset, I use a 52833 Development...
I have an application based on the peripheral uart sample, using NCS 1.8.0. I need to build in a version string that is queryable, so that anyone who connects to the device...
When i intially burn the code on dk, my dk should be in system off mode ie all functionality should be off. Then i want to press a button for 5 seconds with which the device...
Hi,
I am using the nrf52840-DK with the nRF Connect SDK version 1.8.
I have modified the central_multilink sample to connect to a BLE peripheral which requires a secure...
Hi,
We have a mature product based on the STM32 ARM processor family running the uCOS OS and our development toolchain is IAR. The workflow has worked well in the past when...
Dear all,
I ran LPCOMP example from SDK16 on nRF52 DK and it works just fine.
But I've occurred some problem modifying reference voltage. I init the lpcomp the same...
Hi ,
I have my own custom nrf52832 pcb. I have 2 chips on my pcb.
I program my device with Nrf52 Dk.
When I program MCU 1. The program is uploaded successfully and i...
Hai
I'm using nrf52811 and sdk17.1.
I tried all peripheral examples But I can't set advertising data to more than 31 bytes.
If I increase the data size some parameters...
Hi , I am using ZEPHYR rtos , and using the internal bootloader and its working fine and there are two images but now my code size has increased and i can not store 2 images...
Hi
I want to use app_uart_put() to send an array which is over 4096 bytes.I try to change the value of UART_TX_BUF_SIZE to 10K bytes，then call the app_uart_put() to send...
