Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
The Thingy:52 application uses LIS2DH in low power standby mode and the MPU-9250 for advanced motion tracking.
Why machine_learning firmware used LIS2DH sensor instead of...
Hello developers,
I am using nRF52840 feather from adafruit as a ble central board.
FIrst of all, I tried to filter just only for my beacons with UUID. I saw a ble central...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0, without any change in the code. When I use nrfConnect...
Good day!
I have a problem with bootloader and custon DFU transport on nRF52840. What I do:
Transfer DFU over mesh using vendor model (it was implemented for MESH SDK...
Hi.
We recently started a project with the Movesense sensor that uses the nRF 52832. We would like to receive advertising packets on a sport field with a cellphone. The...
Hello everyone, I am developing a system with multiple peripherals to a central board. How many peripherals can keep connecting with central at one time? I made some peripherals...
https://devzone.nordicsemi.com/f/nordic-q-a/65059/buttonless-dfu-on-nrf52832
When I try to DFU from NORDIC_BUTTONLESS , nRFConnect disconnects from it and connects to DFUTARG...
Hello,
I get an error message when running this function:
int ret = i2c_reg_write_byte(data->dev, cfg->i2c_addr, LSM6DSOX_INT1_CTRL, test);
I know 0x0BAE0002 error means...
Hello, With nRF5 SDK 17.1.0 release a new ifdef NRF_BLE_LESC_GENERATE_NEW_KEYS in nrf_ble_lesc.c has been added. Could you please clarify what the intention is of this generating...
Hello Team Nordic,
I think there is still a problem in the SDK 17.1.0 if not using a Softdevice (with SD all is OK):
in "nrf_drv_clock.c" -> "nrf_drv_clock_init(void)...
Hello Nordic team,
I am building an IoT solution and plan to use the nrf9160 just as a stand alone modem. App will reside on a separate MCU and talk to Nrf9160 on uart...
