Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
How much i can apply maximum and minimum voltage at Analog pin of nRF52832 controller IC? And Please also guide me is there any mention in the nRF52832 Datasheet.
Hi all,
I am using SDK = 15, softdevice = v6, chipset:nrf52810
I have used ble_app_uart and SAADC example code for one of my application, its working fine, and next i...
Hello,
I'm using nRF v1.5.1 SDK.
If I have my RX buffer to be of size say 6, and I transmit 7 bytes then my code will detect a full RX Buffer and go to the endrx_isr...
Hello,
Looking at the errata entry [78] TIMER: High current consumption when using timer STOP task only , I see that it recommended to use TASKS_SHUTDOWN instead of TASKS_STOP...
Hi everyone,
what are the tolerances of the internal reference voltage of the ADC (0.6V) at room temperature? I know the tolerances are included in the gain error and are...
Hello,
I'm following this documentation Doc to include Fota upgrade on peripheral LBS sample but I have the following problems:
1) all file .bin like ( app_update.bin...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
Hello,
Following to this ticket , I started with an existing Segger embedded studio project from the SDK to port my project from Keil to SES 5.62 .
Now, the project works...
How long does it take to perform a soft reset (using sd_nvic_SystemReset()/NVIC_SystemReset())?
Looking at power measurements (attached) it seems to take about 730 ms (...
Hello developers,
I would like to combine BLE Central with USB HID. I am using the SDK example "BLE_Central_multilink", I can get signal from BLE modules.
Now I want...
I tried to program the Blinky sample which just blinks an LED to the Network core of the nRF5340 DK but doesn't seem to work. However, when I look at the docs I do see that...
Hi
I am a beginner of bluetooth
I want to build BLE connection between nrf52833 and nrf52810 as soon as possible (maybe in 100-200ms)
can I achieve that by config Advertising...
Hi Nordic,
I am facing strange behaviour with nrf9160 aws iot example where I am trying for fota update.
My device is sending data to AWS IOT every 5 minutes as it will...
Hello again Nordic World,
We have been using a couple of the Nordic dev boards (PCA10028, PCA10040) as uart central devices in our test system for a while and have just...
