Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hey, I'm new to this so I will need some help. I have custom board with 453-00059 ( BL653ÎĽ with nRF52833 ) and first I want just chip to be seen on my bluetooth devices list...
Hi there,
We are trying to download and install the nRF Connect SDK v1.5.1, which seems to be the latest version on Toolchain Manager.
However, after installation, the...
I'm using the Azure Iot hub example a base for a new project I'm working on.
I've copied the example into its own folder, and can run it and connect my Azure IoT hub.
...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
nrf52840 is configured as BLE central with bonding enabled...
Hello,
I'm trying to use PPI over PWM to, at the end of one single PWM period, disable the PWM and switch one GPIO (later, I'll use it for more complex task, but I start...
Hello Everyone!
I am new to nRF boards and still in the learning phase. I want to send some data from nRF52840 to an LCD display through SPI. I am currently using the SPI...
Hi Nordic
One of my customer develop a system with ESB(Enhanced ShockBurst). They employs nRF51802 in their project.
In their system, above 40-50 Tx devices transmit message...
Hi Nordic Team,
I've read some forum discussion about using NAND SPI Flash Chip as external flash storage. These are two chips I'm considering :
W25N01GVZEIG ...
Hi,
We are currently trying to create a small test code to test multiple operator with different modes:
- lte-m1 or lte-nb1
- edrx 0s, 5.12s, 10.24s
- with and without...
Dear Nordic Team,
I recently ported the BLE UART example project for the PCA10056 to the PCA10059 dongle (SoftDevice 113). I added some minor changes like RX/TX pins, GPIO...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server x 2
Software...
Hello,
I cannot find a download link for the 17.0.0_9d13099 build of the SDK. Is it publicly available and if not, can a private link be provided? Have some dependencies...
Hi,
I am using nrf52840, need to modify the bootloader to lookup a big bitmap table. But since the table is big, it cannot allocate within the bootloader Rom area.
Is...
Hi
i am using nrf9160 based custom board with zephyr, and trying to build GPIOTE with interrupt for a button, and led finally connect with PPI
i have been trying for...
