Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I am using nrf mesh 5.0 sdk and nrf 17.02 sdk for nrf5832 board and want to implement scene setup server model in the light ctl and light lc model combined. I am not...
Hi,
We are working on our new product which needs a BLE connection with a mobile phone.
Our requirements are as follow:
1) Four digital output. (It's preferred to be...
Hello,
From the ble_app_uart example I created a version where instead of the UART the incoming data over BLE is processed using the scheduler.
Processing is not much...
Hi, i develop a bluetooth project with nrf52832 anad i am unexperinced about this topic. I searched for 2.4 GHZ antenna desgin bu can't found. There is a few topics about...
HW: nrf52833-DK
SW: SDK v16.0.0 and SoftDevice s140
We are using nRF52833 BLE direction feature and read IQ samples produced by BLE Radio.
The format of the IQ samples...
I am working on porting a project from the old sdk to the nrf5340 and the nrf connect sdk documentation seems to be incorrect and i am having major issues even getting this...
SoC: nRF52810
SDK: 17
Hello,
I want to confirm whether BLE_DFU_ENABLED is used or not.
InfoCenter ( https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/group__ble__dfu__config...
Hi,
I use the app "asset-tracker", and i would like to configure an external uart to connect a sensor to the board.
I modifed the code but i can't detect any new COM from...
Hi,
I am using nrf51422 and s130 softdevice for multirole. Is there any way to reduce the receiver power during scanning so that the overall current gets reduced?
Hi,
I'm trying to implement remote provisioning on an altered version of the light switch example in the SDK for Mesh v3.2, on nRF52832 development kits. The code I'm using...
I am using nrf52832, i want to send the sensor data continuously via ibeacon.
but while uisng sd_ble_gap_adv_set_configure() function return error NRF_ERROR_INVALID_STATE...
Hello,
I am testing a light switch system where each switch is capable of controlling multiple bulbs via multiple groups stored on the switch. I have noticed in the example...
As of what I've read in [1], nRF9160 uses ARM Cortex-M33. I'm not sure which qemu of the Zephyr OS is compatible with ARM Cortex-M33 the most ? qemu_cortex_m3 or none of them...
Problem:
I am trying to measure two voltages from the SAADC. I have built my application on the ble_app_uart__saadc_timer_driven__scan_mode example . It is using one SAADC...
