Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
To the kind attention of Nordic support team,
We are very interested indeed in using your nRF52840 and nRF52810 devices in our projects. We also would like to use your gazell...
Hi,
I have used nRF52832 with my Python code succesfully many days. Suddenly it stopped to working and gives me an error message: NordicSemiException: Failed to ble_gap_scan_start...
Hellou. I'm developing application, which is modifiaction of light switch demo. I need use 128 servers and one client. But when I redefine in SERVER_COUNT to 128 in client...
Hi all, ( nRF52 DK, SDK 15.3, S132 )
Many asking about how to add 2 "service data" in the GAP advertising, but no real answer on the solution !
The first service data...
Hey everybody!
I'm trying to implement the following use case.
Android device connects to nRF52, bonding occurs, android device is put into nRF52 whitelist, after this...
Hello, I am trying to combine light switch client example with fds functionality.
For these I did next steps:
Included all ‘c’ files from the fds example to the light...
I notice that the USB Serial (the lowest numbered COM port of the three, that's connected to the Cortex-M33) isn't opened in a Serial Terminal before the application starts...
Hello:
When I try to use mesh, I found that the bootloader never work in low power mode. If I only program application into the nrf52832, the power consumption of its low...
