Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hey guys,
I am currently using the nRF24L01+ (more specifically the module that has +pa +lna), and I am experiencing some odd behavior. I will briefly go over the devices...
Before buying the Teledyne BPA low energy protocol analyzer, I asked a question here based on the Teledyne not supporting BLE 5.
I was told that it would work fine with...
Hi all, I'm working on creating new model for sending a byte from proxy client based on Generic On Off model. For working with light-switch proxy example , I used NRF Mesh...
Hi,
I am developing a sensor application with the nRF52832 on a custom board.
Therefore I designed a GATT with nRF5_SDK_14.0.0 softdevice which exposes 3 custom characteristics...
I’ve downloaded nRF5_SDK_11.0.0_89a8197 and starting with examples from \examples\ble_peripheral\???\pca10040\s132\arm5_no_packs\
I would like the other device to request...
I want to interface ADXl345 with nrf51 SDK. suppoose my device address is 0x53 and register address is 0x2D and i want to write value 8. now nordic i2c has function nrf_drv_twi_tx...
Hi We have a generated a key pair using ECDSA secp256k1 ```
err_code = nrf_crypto_ecc_key_pair_generate ( NULL , & g_nrf_crypto_ecc_secp256k1_curve_info , & private_key...
I'm trying to run a project baset on the ble_app_proximity example project . When I trying to call a nrf_sdh_enable_request() function library goes into an infinite loop....
Hello,
I would like to know if you can point me where to find the electrical characteristic of the module nRF9160. I'm looking for :
- Then maximum current the module...
I work on your new Mesh SDK 3.1.0 and I have some questions for you.
First it is about DFU over Mesh. I think your documentation is very weak. I understand that they are...
Hello Nordic, we use the nrf52 proprietary protocol in the project, it will send 200 data per second, and no ack confirmation, the application data length is 25 or 32 bytes...
SDK 15.2
Segger Embedded Studio Release 4.12 with DEBUG on
Segger Ozone V2.60k
FreeRTOS 10 from SDK (same issue with FreeRTOS 10.1.0 source files and original ported...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
