SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
I have a project for nRF52 in VS Code. The project was able to compile and everything worked fine. However, after about a month, I reopened the project and now there...
I am developing LTE-M software on nRF9160. Previously, I checked that it runs well with nRF9160DK. Now I try it with my own board.
First, only for testing, I made following...
Hi, I'm trying to set up wireless audio stream using 2 nRF52832 Dev Kits and SGTL5000 audio boards. SDK: nRF5 SDK 17.1.0 For the wireless protocol I've used ESB, and the program...
Hi, I've been trying to modify some of the nRF5 SDK 17.1.0 BLE HID examples to make the nRF appear as a BLE HID Braille Display, that would be recognized in Android's TalkBack...
Hello,
I'm modifying the code of Wireless timer synchronization among nRF5 devices blog to use RTC instead of two TIMERs. I started with the code on Git for SDK 16. Writing...
Today I opened VS Code to find all my Zephyr/NRF #includes have the red squiggly lines with an error such as "cannot open source file zephyr/types.h". Right click -> Go to...
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
Hello,
I am trying to interface a TCA9548A Multiplexer on my custom board. I am able to set up the channels and read the channel status' with device_get_binding successfully...
I'm just trying to get my feet under me to write some code for the nina-306 module. I'm playing along, and following the dev academy course. I can't tell if this worked or...
I'm trying to do my first Blinky app with nrf52811. I followed all installation procedures by DevAccademy.
I created a new application by the available sample (blinky led...
Hello,
I am currently using the BLE NUS example from the Nordic Dev Academy course for BLE ( https://github.com/NordicDeveloperAcademy/bt-fund/blob/main/lesson4/blefund_less4_exer3_solution...
Hi all,
I am trying to use MCUBoot on the nRF52840, and am having troubles with this: Whenever my device boots, it always immediately goes to bootload mode and I can't get...
hi all,
ST7735 driver for TFT Display which is tested using example/peripherals/GFX library, we want to test touch screen for this display ,the touch screen driver used...
I am currently working on a project using the nRF52840-DK and the Power Profiler Kit II. I have created an application based on the "NFC System Off" sample. However, I am...
Hi could you provide any insight on the following issue:
Source code in main.c
#include <zephyr/kernel.h>
#include <zephyr/device.h>
#include <zephyr/drivers/sensor...