Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
Hi,
I am working on nrf52832 and using SDK 16.
I try to debug the ble_app_buttonless_dfu example, which give error on line 853 in main.c. err_code = ble_dfu_buttonless_async_svci_init...
We are in the process of developing a product using the Thingy91:X as reference.
We need to modify the hello-nrfcloud firmware to suit our application.
Could you suggest...
I am currently working with the Matter sample project and have encountered a question regarding the diagnostic log function. I would like to inquire about how to enable the...
I'm using nrf52840, v3.0.2, scanning BIG/BIS and printing out the BASE.
I first scan the extended broadcast with the label broadcast_id, and then establish synchronization...
I wish to install this program as stated in nRF Connect for Desktop. The install hangs at Downloading files... I am on Windows 11. I tried a few times with the same result...
I am puzzled by what I have observed using retained ram on NRF54L15. I have this overlay (see below). Essentially created 16 KB SRAM at address 0x2002C000. I have a struct...
We are trying to add ble mesh functionality to our current product, but encountering an error.
We are copying code from the ..\v3.0.1\zephyr\samples\bluetooth\mesh_demo...
To generate build configuration and build the app, you first need to: touch ncs/v3.1.x/bootloader/mcuboot/boot/zephyr/boards/nrf54l15dk_nrf54l15_cpuapp.conf
or copy it from...
I am currently working on the Matter certification for the light_bulb sample project , where I have integrated the Diagnostic Logs snippet during compilation. However, during...
