Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I am trying to run the system_off sample project to measure some low power currents. The sleep works as expected but once it reaches:
It does not go into deep...
If I wan to use the nRF52 as a Radio and not support any protocols.
I am looking to use this as a base band waveform processor and transverting down below 1Ghz.
What is...
I'm attempting to create firmware using nRF Connect SDK. Thoroughly studied these guides:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started...
I'm referring to nRF5 SDK 17.0.2. In 'external/freertos/config/FreeRTOSConfig.h', the value 'configLIBRARY_LOWEST_INTERRUPT_PRIORITY' is set to 0xf, but the nRF51/52 only...
Hello! I'm trying to use this low power UART sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/samples/peripheral/lpuart/README.html I have a problem...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 Base source: C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\peripheral_hids_keyboard I add uart implementation from following...
I need nRF52840 revision 3 mounted development kit board, for trial rev 3 's approtect feature. But I don't know when is the rev. 3 mounted development kit board available...
when i make Rx output succefully.i add some configuration in main.c.i can print iq data.there is link that make me to learn to print iq data.
ok,i get iq data in here.but...
I'm trying out DFU functionality using nRF52840-PreviewDK and UART transport
It looks like I can disable the requirement for a signature when downloading an APP or SD (SoftDevice...
I have looked all over the product specification and the website and cannot find any information related to matching an antenna for this device.
What I am looking for are...
Hi I used your nrf toolbox Uart app to communicate from an Android phone to the module to send and receive bytes. The app was automatically updated a few days ago, now i cant...
Hi everyone,
I am not able to connect my J-Link plus compact with the programmer in nRF Connect.
It returns the error Unsupported device. The detected device could not...
Hi,
I am using SGTL5000 CODEC to playback the LINEIN and I am using the SGTL5000 driver from this link
I am using this I2S configuration
For I2S Loopback code itself...
