I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
I am currently working with the nRF52 DK and have compiled some code to read ADC values. This code works fine with the nRF52 DK but I am having trouble getting it to work...
Hello everyone, I'm developing a wearable device based on nRF52832 which reads IMU (ICM20948) data using TWI.
The problem is that if I try to use the code with a custom...
hello everyone,
in my project i need to advertise the sensor data as well as connecting the BLE TAG . in detail i am using nrf52810 with mpu6050 and i want read the accelerometer...
Hello,
During my evaluation of nRF52840 I discovered an issue which prevents the device from joining a Zigbee network successfully.
I'm using out of the box zigbee/light_bulb...
Hi,
I've installed all by the book watching the installation videos and I have a problem building in VScode
when I try to build with nrf connect app window I get this...
Hello,
To preface, this project was redirected to me and I have very little experience using SoCs. Happy to provide any additional information and apologies for issues in...
Hi!,
I am trying to create an application with BT Mesh using the nrF52840 DK and two nrF52840 Dongles with an OnOff Model Server and an OnOff Model Client respectively....
Hello.
I am new to Zephyr, I know how to digital read the pin which is used as INPUT
#define SW0_NODE DT_ALIAS (sw0)
static const struct gpio_dt_spec DOUTINPUT = GPIO_DT_SPEC_GET_OR...
Greetings,
I'm using NRF52840 with softdevice and nRF5_SDK_17.1.0 on NRF52 DK.
The shutdown_handler in my code is as follows:
There is a secure bootloader from Nordic...
Hi, I am using nRF52832 module as connectivity chip (GAP peripheral, GATT server) with ble_app_uart_pca10040_s112 as source.
I am using nRF connect app to test data communication...
I am currently developing a feature for a BLE module to pass certifications (BL654 Laird, based on nRF52840). My application runs on SDK 15.0.0. I used the "radio_test" module...
My overall goal is to update the percentage of battery left in the advertiser and then either go to a nine second sleep to conserve as much power as possible and then wake...
I am following the instructions to enable micro-ecc support for an example code ( secure bootloader ble s132 pca10040 debug). I am using SDK 17.0.2.
I have successfully...
I'm sorry, maybe it's me, but your SAADC documentation leaves much to be desired, as I was easily able to implement getting readings from a single analog input (non-blocking...
Hi,
Trying to do a very simple thing.
I want to start a new project from a sample project, but I want my new project to be in a different folder
Load nRF Connect...
