I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Dear all and Nordic Staff:
Thanks for your support as usual.
I have a new application project with BLE and Zigbee dual stack protocol for industry market.
May you suggest...
One of the nRF52840-DK (PCA10056 v2.0.0) we are using as a programmer and debugger for our custom board has started repeatedly resetting the custom board whenever an RTT console...
ble_gatt_db.h and ble_db_discovery.h each contain #defines that are problematic, BLE_GATT_DB_MAX_CHARS and BLE_DB_DISCOVERY_MAX_SRV respectively.
Of course, one can change...
We use NRF52832 in the remote control of the car。 We measured the average current of power consumption at about 1uA.Every 300ms, the current curve bounces to the transient...
I would like to use the RTC in the nRF52833 as a clock-calendar. The device will normally be powered by the USB Vbus but must have power fail protection to insure the integrity...
Hello,
I would like to create a star network (with no routers) in ZigBee with nRF52 (also with multiprotocol BLE). I examined the relevant SDK (nRF5_SDK_for_Thread_and_Zigbee_v4...
My setup is a custom board with the nRF52832 and a remote BLE client e.g. nRF Connect tool kit on an Android phone.
The application periodically broadcasts a 'beacon' but...
I am using Nordic SDK v15.3.0.
I have set all the required parameters and content before I call the API "ble_advdata_encode(..)". I ran into two issues one of which I can...
I am using SDK version 15.3.0 and would love to know what exactly is the meaning of the first parameter "size of event" used in the macro APP_SCHED_INIT(X,Y)?
I treat "events...
I have installed Segger Embedded Studio for ARM V5.32a.
I am trying to build the example project under ble_peripheral/ble_app_uart.
I have installed these packages in...
Dear community, Dear Nordic engineers,
For some reason I cannot connect my custom board to the nordic cloud. Previously I have followed the described procedures with the...
Hello,
I have a custom nrf52832 board with a SparkFun HX711 load cell.
I've developed my firmware using Segger Studio testing my data through a BLE connection with the...
Hi,
I ported my application from SDK 12.3 to SDK 17.0.2. Unfortunatley it isn't running on the board, but the only thing I have is a warning which I'm hoping is the issue...
