I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi Nordic:
It seems that mesh LPN can receive secure beacon via friend node, and if has no friend, LPN also can receive secure beacon if MESH_FEATURE_LPN_ACT_AS_REGULAR_NODE_OUT_OF_FRIENDSHIP...
I'm running some power tests on the nRF52 DK and, after fiddling with some of the power settings, I'm managing to get an idle current of about 1.8uA on the coin cell, and...
I'm sorry to ask a question that I'm sure has been answered before, but I can't find another post similar enough to be of help. I have an HID application that bounces back...
Dear All,
We are currently developing a low power application for the nRF9160, with ncs zephyr version 1.2.0. For our application we want to trigger an interrupt on both...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
Hi,
I would like to get some information about the reset's reason of my nrf9160 like
- The reason is due of an assert type "xxx"
- Where is the stack pointer
- .....
Hello,
I'm developing a BLE device and it consist of nRF52833 and a external UART component.
ble_app_uart example in SDK v17.0.0 is replaced app_uart to libuarte. The...
Hi,
I would like to know if we can enable codded phy while using mutli peripheral in conjunction with mutli central. Also peripheral should be scannable and connectable...
When creating dfu package using nrfutil, an error is displayed.
When I looked for and checked the file where the error occurred, a problem occurred in Python's max...
I am trying to run nrf52840 chip without debugger.
I want to run peripheral_uart example just to show advertising of bluetooth.
And when I use west debug --runner=jlink...
Hi,
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Then I flashed the agps code because just want to send GPS coordinates on the...
I am having issues using port pin 1.00 on the 52840 as GPIO. It will just not toggle.
I can successfully use most other pins, even those on the higher port. For example...
Hi
I have 2 identical PCB just out of production - same FW - one is drawing higher current (about 600uA).
The issue is found in mass production and about 1% is having...
I'm using nRF52 DK to send SAADC data to mobile app "nRF Connect" over BLE.
I'm using this code to send the data, but the mobile app "nRF Connect" can only show integer...
