Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
How wide are the peaks? I know that it depends on many factors how high and long the peaks are. Currently we have measured peaks of 450 mA for 40-50 ms in our application...
Hi,
I am trying to run the Zephyr BME280 sensor sample application (using nRF9160 DK) in NCS1.3.1, but get the below error:
My prj.conf is as follows:
And board...
Hi all:
I install "nRF Connect SDK v1.3.0" by Toolchain manager,
but it always show "Failed to clone the repositories".
Could you have any suggestion?
best...
I am trying to interface my nrf51 DK with the Lis3dh sensor . I have one reference code by elmot for the project and it is working.
https://github.com/elmot/nRF51822xxAA...
Hi,
I'm comparing the nRF9160 DK and Thingy 91. The purpose is to copy the LTE RF design for a Band-20 application. The GPS will not be used.
Question: Is the complexity...
I have bought two thingy 91 to develop the tracker using GPS and accelerometer. I did all the step by step to load pre-compiled hex file given on the website. Then I created...
We are making customize the wearable who records the data from the accelerometer and GPS sensors and sends it back to our server. SO, we decided to use thingy 91 chip has...
Hi,
We built the Blinky sample with NRF Connect SDK 1.3.1. It works fine on NRF52833 DK, but when flashing on external custom NRF52833 board the firmware won't start without...
Hello,
I am trying to integrate the Unity test framework into our project and running into issues with how to add additional test files. Nordic provides one example project...
Hi,
I am developing a project where I have NRF52840 as a device and another NRF52840 as a BLE USB dongle connected to PC.
I have to improve the BLE data rate between the...
Hi,
I have a NRF52840 device connected by BLE to another NRF52840 BLE USB dongle connected throw USB to a PC application.
I want to synchronize the RTC on the connected...
Hello I am currently working on a project with the XM122 / XB122 kit for an evaluation, the XM122 card integrates an nrf52840 MCU and a radar sensor;
The goal of my project...
Hi, I'm using nrf52833 with SDK 17.0.0.
I want to send SAADC data over BLE.
So, I want to see data in my phone.
I've modified codes.
I want to use macro(ble_nus_data_code...
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/simple-application-level-authentication
Hi
I am looking to make this example work but this post is old...
